'99 dodge dakota

Discussion in 'Off-Topic' started by tksti, Nov 18, 2008.

  1. tksti
    Offline

    tksti New Member

    Likes Received:
    0
    Trophy Points:
    0
    does anyone know of anyone that check out why the passenger side headlight is dimmer than the drivers side. I already checked all the grounds and bought new headlight. so something else is wrong. anyone??
     
  2. AWDimprezaL
    Offline

    AWDimprezaL has more posts than you

    Likes Received:
    1,818
    Trophy Points:
    573
    connections AT the bulb.
     
  3. tksti
    Offline

    tksti New Member

    Likes Received:
    0
    Trophy Points:
    0
    the connections look good. there is no corrosion
     
  4. AWDimprezaL
    Offline

    AWDimprezaL has more posts than you

    Likes Received:
    1,818
    Trophy Points:
    573
    are they tight? try wiggling the connection at the bulb
     
  5. WRX1
    Offline

    WRX1 _ Staff Member

    Likes Received:
    727
    Trophy Points:
    348
    Voltage?? If you have the same voltage at the bolb, swap bulbs from side to side to see if the problems moves.


    Russ
     
  6. subytek
    Offline

    subytek Well-Known Member

    Likes Received:
    0
    Trophy Points:
    101
    Check the fuse, even if it's blown most headlights light up halfway.
     
  7. tksti
    Offline

    tksti New Member

    Likes Received:
    0
    Trophy Points:
    0
    tried it
     
  8. tksti
    Offline

    tksti New Member

    Likes Received:
    0
    Trophy Points:
    0
    checked it
     
  9. tksti
    Offline

    tksti New Member

    Likes Received:
    0
    Trophy Points:
    0
    did not try it yet. got to find my multimeter did swap bulbs that did not work
     
  10. WRX1
    Offline

    WRX1 _ Staff Member

    Likes Received:
    727
    Trophy Points:
    348
    So you swapped bulbs from side to side, and the same side stayed dim with 2 different bulbs??

    If that is the case, you are not getting full voltage to the bulb. So then you are looking at a wire/connector problem. Just dump in a couple of relays and rewire them. Probably get it done in a matter of a hour.

    Russ
     
  11. tksti
    Offline

    tksti New Member

    Likes Received:
    0
    Trophy Points:
    0
    that is probably the best way of going about this problem. I was trying to stay away from it. I hate wiring
     
  12. PRA4SNO
    Offline

    PRA4SNO Well-Known Member

    Likes Received:
    23
    Trophy Points:
    123
    its a dodge dakota? heh
     
  13. tksti
    Offline

    tksti New Member

    Likes Received:
    0
    Trophy Points:
    0
    its actually my dads truck. He has been talking about fixing it for over a month. I finally went over there to look at it and I can't figure it out either. I wanted to stay with the stock wiring but maybe the rewireing route is the best way to go.
     
  14. WRX1
    Offline

    WRX1 _ Staff Member

    Likes Received:
    727
    Trophy Points:
    348
    Well, check the voltage. Maybe it is just a bad connector (I have seen that). Maybe you have power on the wires and it is just the bulb connector. If that is the case, then you just need to replace the connector. If you are only getting 5-6-7-8 volts on the wires, then it is time to pull the wires and hunt down the problem, or rewire.

    Russ