WTBorrow Clutch alignment tool

Discussion in 'For Sale : Car Parts' started by wrxpeed, Oct 29, 2007.

  1. wrxpeed
    Offline

    wrxpeed CobraPeed

    Messages:
    1,864
    Likes Received:
    2
    Trophy Points:
    223
    Location:
    Maple Grove
    I'm doing my 5mt swap this weekend and need a clutch alignment tool. Anyone around here have one to borrow to me?

    Thanks,

    Bryan
     
    wrxpeed, Oct 29, 2007
    #1
  2. Dynapar
    Offline

    Dynapar Well-Known Member

    Messages:
    10,814
    Likes Received:
    31
    Trophy Points:
    358
    Location:
    Orono, MN
    Talk w/ fuji. he is pro at lining up clutches.
     
    Dynapar, Oct 29, 2007
    #2
  3. Jackstand
    Offline

    Jackstand Well-Known Member

    Messages:
    2,116
    Likes Received:
    4
    Trophy Points:
    123
    Gender:
    Male
    Location:
    St Louis Park
    Yeah he uses is finger alignment tool :biggrin:
     
    Jackstand, Oct 29, 2007
    #3
  4. mayhem83
    Offline

    mayhem83 Well-Known Member

    Messages:
    911
    Likes Received:
    0
    Trophy Points:
    101
    Location:
    Stacy, MN
    I have a metal one (from a busted trans) you can use but you will need to come to Stacy to get it. Let me know.

    Mark Utecht
     
    mayhem83, Oct 29, 2007
    #4
  5. readymix
    Offline

    readymix ...Lest ye be trod upon... Staff Member

    Messages:
    12,344
    Likes Received:
    2,892
    Trophy Points:
    473
    Location:
    Eloh, El
    I have one you can borrow. I'll grab it. When do you need it?
     
    readymix, Oct 29, 2007
    #5
  6. wrxpeed
    Offline

    wrxpeed CobraPeed

    Messages:
    1,864
    Likes Received:
    2
    Trophy Points:
    223
    Location:
    Maple Grove
    thanks, but it looks like the mix has me covered.


    Cool. I'll need it this weekend, most likely saturday since friday night is when I'll be pulling all the Auto stuff. I could swing down and meet you somewhere friday night.

    Thanks
     
    wrxpeed, Oct 29, 2007
    #6
  7. readymix
    Offline

    readymix ...Lest ye be trod upon... Staff Member

    Messages:
    12,344
    Likes Received:
    2,892
    Trophy Points:
    473
    Location:
    Eloh, El
    NP man. I'll PM you my cell number. We could meet at Firestone on Friday. Don't know how far that is for you, it takes me about 20min to get there. Whatever, we can figure it out later.
     
    readymix, Oct 29, 2007
    #7
  8. Chux
    Offline

    Chux Well-Known Member

    Messages:
    5,947
    Likes Received:
    1,489
    Trophy Points:
    398
    Gender:
    Male
    Location:
    Independence, MN
    I'm not sure if this works on EJ-series trans's.....the starter hole might not be in the right place. but on the EA ones, you can reach the PP to flywheel bolts through the starter hole. put the clutch kit together as you would normally, but only put those bolts in finger tight. than the clutch disc can move around under the PP. making mating the engine and trans about 45 million times easier.....

    than just tighten those bolts through the starter hole by turning the engine over from the crank bolt.
     
    Chux, Oct 29, 2007
    #8
  9. wagonL
    Offline

    wagonL Well-Known Member

    Messages:
    712
    Likes Received:
    1
    Trophy Points:
    203
    tsk tsk tsk...fuji likes to put his finger in a lot of things :p...



    mechanically wise...
     
    wagonL, Oct 29, 2007
    #9
  10. wrxpeed
    Offline

    wrxpeed CobraPeed

    Messages:
    1,864
    Likes Received:
    2
    Trophy Points:
    223
    Location:
    Maple Grove
    the Firestone is good for me if its good for you friday evening.
     
    wrxpeed, Oct 30, 2007
    #10
  11. readymix
    Offline

    readymix ...Lest ye be trod upon... Staff Member

    Messages:
    12,344
    Likes Received:
    2,892
    Trophy Points:
    473
    Location:
    Eloh, El
    Done and done. I'll be there Friday with the alignment tool.
     
    readymix, Oct 30, 2007
    #11