WTB: EJ257 Case halves

Discussion in 'Want To Buy : Cars/Parts' started by mn_sti, Jun 30, 2015.

Thread Status:
Not open for further replies.
  1. mn_sti
    Offline

    mn_sti Well-Known Member

    Likes Received:
    12
    Trophy Points:
    203
    I am looking to buy a set of case halves for an EJ257. Let me know what you have (or know of).
     
    mn_sti, Jun 30, 2015
    #1
  2. Sjogun
    Offline

    Sjogun Active Member

    Likes Received:
    257
    Trophy Points:
    73
    I have some ej255 case halves.
     
    Sjogun, Jun 30, 2015
    #2
  3. Ryan FailRad
    Offline

    Ryan FailRad Well-Known Member

    Likes Received:
    1,061
    Trophy Points:
    248
    Me too, how much are you willing to spend?
     
    Ryan FailRad, Jun 30, 2015
    #3
  4. mn_sti
    Offline

    mn_sti Well-Known Member

    Likes Received:
    12
    Trophy Points:
    203
    Depends on what kind of shape they are in and how much I have to spend to get them machined. Any photos?
     
    mn_sti, Jun 30, 2015
    #4
  5. Ryan FailRad
    Offline

    Ryan FailRad Well-Known Member

    Likes Received:
    1,061
    Trophy Points:
    248
    I kinda left them out in the garage last winter so there is some surface rust in the cyclinders, nothing super terrible though. They are in Hudson Wisconsin, I am not.. So no pictures.
    @Sjogun is probably a better source honestly.
     
    Ryan FailRad, Jun 30, 2015
    #5
  6. idget
    Offline

    idget Want to pokéman? PM ShortytheFirefighter Staff Member

    Likes Received:
    4,334
    Trophy Points:
    398
    idget, Jul 1, 2015
    #6
    Ryan FailRad likes this.
  7. yuseforester
    Offline

    yuseforester Well-Known Member

    Likes Received:
    253
    Trophy Points:
    148
    Oh no....where in Hudson?!
     
    yuseforester, Jul 7, 2015
    #7
  8. Ryan FailRad
    Offline

    Ryan FailRad Well-Known Member

    Likes Received:
    1,061
    Trophy Points:
    248
    Just past Hudson in Roberts Wisconsin actually.. I don't really have a reason to go out there so I haven't been out there yet to get pictures etc
     
    Ryan FailRad, Jul 7, 2015
    #8
  9. yuseforester
    Offline

    yuseforester Well-Known Member

    Likes Received:
    253
    Trophy Points:
    148
    Lol, ok, you had me worried for a minute...LONG story...
     
    yuseforester, Jul 8, 2015
    #9
    Ryan FailRad likes this.
  10. Ryan FailRad
    Offline

    Ryan FailRad Well-Known Member

    Likes Received:
    1,061
    Trophy Points:
    248
    Story time!!
     
    Ryan FailRad, Jul 8, 2015
    #10
  11. yuseforester
    Offline

    yuseforester Well-Known Member

    Likes Received:
    253
    Trophy Points:
    148
    You guys have already heard that story...I even through a party to celebrate recovering from it...well at least in part...
     
    yuseforester, Jul 8, 2015
    #11
    Ryan FailRad likes this.
  12. Ryan FailRad
    Offline

    Ryan FailRad Well-Known Member

    Likes Received:
    1,061
    Trophy Points:
    248
    Makes sense!
     
    Ryan FailRad, Jul 8, 2015
    #12
  13. Dynapar
    Offline

    Dynapar Well-Known Member

    Likes Received:
    31
    Trophy Points:
    358
    I have a set which needs machining. Ej257 from an 05 STI. Engine had ringland failure. Cyljnders need to be bored out to 100mm most likely. Would entertain offers via pm. Otherwise they will sit on the shelf for a rainy day.
     
    Dynapar, Jul 8, 2015
    #13
  14. mn_sti
    Offline

    mn_sti Well-Known Member

    Likes Received:
    12
    Trophy Points:
    203
    PM sent
     
    mn_sti, Jul 8, 2015
    #14
  15. mn_sti
    Offline

    mn_sti Well-Known Member

    Likes Received:
    12
    Trophy Points:
    203
    Picked up a case today (thanx Dynapar). Time to get this project going again!
     
    mn_sti, Jul 11, 2015
    #15
  16. Dynapar
    Offline

    Dynapar Well-Known Member

    Likes Received:
    31
    Trophy Points:
    358
    No problem. Glad i was able to help. Good luck with the build!
     
    Dynapar, Jul 13, 2015
    #16
Thread Status:
Not open for further replies.